{"title":"Lamber","description":"\u003cp\u003eLamber builds Italian commercial warewashing equipment, and this lineup runs to the glass and dish racks that go with it: open racks without dividers for mixed ware, compartment racks in nine, sixteen and twenty-five cell layouts, and tall versions with the extra clearance stemware needs. Bars, cafes, hotels and restaurants sized for a 16 by 16 inch machine use these to protect glassware and cut hand-polishing time after every cycle. Rack fitment is machine-specific, so check the model called out on each part, then review \u003ca href=\"\/collections\/glasswashers\"\u003ecommercial glasswashers\u003c\/a\u003e and \u003ca href=\"\/collections\/commercial-dishwashers\"\u003ecommercial dishwashers\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"lamber-l25eks3ph-pass-through-dishwasher-9-000w-rinse-208-240v-3-phase-gravity-drain","title":"Lamber L25EKS3PH Pass-Through Dishwasher, 9,000W Rinse — 208\/240V 3-Phase, Gravity Drain","description":"\u003cp\u003eNine thousand watts of rinse element is what keeps a dish pit moving. On the L25EKS3PH that heating package feeds a 2.1-gallon boiler that lifts a 131-140°F supply to a \u003cstrong\u003e180-195°F sanitizing rinse\u003c\/strong\u003e, and it recovers fast enough that the second rack, the tenth rack and the fortieth rack all come out at temperature. Thermocontrol holds the setpoint through a continuous run, so a Saturday closing shift gets the same result as a Tuesday lunch.\u003c\/p\u003e\u003cp\u003eRacks measure 19.6 x 19.6 inches with 16.3 inches of plate clearance, so dinner plates stand upright and bus tubs go in without breaking down the load. Four cycles — 2, 3, 4 and 15 minutes — cover glassware through soaked pans, and each one draws just 0.6 gallons of fresh water while an 8.9-gallon tank recirculates the wash. Soft start protects glass and light china from the first pulse of the 1,100 W wash pump; the hood latches and the cycle begins on its own, so nobody has to reach for a button with full hands. Detergent and rinse-aid pumps are built in and dose chemical automatically. At 59.5 dB(A) the machine does not add to the noise of the room.\u003c\/p\u003e\u003cp\u003eRuns on hardwired 208\/240V three-phase service, 10,100 W total rating. Water comes in through a 3\/4\" G connection at 20 ± 5 psi; the 1-1\/4\" gravity outlet needs a floor drain below the machine. The cabinet is 30.1 inches wide by 26.3 inches deep by 57 inches tall, 308 pounds net and 357 pounds crated. Built in Italy, cETL (cUL US) listed, UL EPH classified, Energy Star qualified, one-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143395618974,"sku":"EUR-L25EKS3PH","price":12203.2,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_L25ek_CC_SH_b2b51389-ca1d-4b44-9718-0da028b1fcd1.png?v=1789708103"},{"product_id":"lamber-l25ekdps3ph-pass-through-dishwasher-drain-pump-9-000w-rinse-208-240v-3-phase","title":"Lamber L25EKDPS3PH Pass-Through Dishwasher, Drain Pump, 9,000W Rinse — 208\/240V 3-Phase","description":"\u003cp\u003eA 30-watt drain pump pushes waste water out under pressure through a 3\/4-inch line, which means this machine does not have to sit over a floor drain. That single component decides a lot of dish room layouts — an island install, a corner against an exterior wall, a retrofit into a building where breaking the slab was never in the budget. The L25EKDPS3PH puts that flexibility behind the largest heating package Lamber builds into this cabinet.\u003c\/p\u003e\u003cp\u003eNine thousand watts of rinse element and a 2.1-gallon boiler take a 131-140°F supply up to a \u003cstrong\u003e180-195°F sanitizing rinse\u003c\/strong\u003e, and Thermocontrol holds that temperature rack after rack through a continuous run — the difference between a machine that keeps up with a rush and one that falls behind it. Four cycles of 2, 3, 4 and 15 minutes handle glassware through overnight-soaked pans, each drawing 0.6 gallons of fresh water while an 8.9-gallon tank recirculates the wash. Racks are 19.6 x 19.6 inches with 16.3 inches of plate clearance. Soft start eases the 1,100 W wash pump into the load so glass and light china survive it, the cycle begins when the hood closes, and built-in detergent and rinse-aid pumps dose chemical without anyone measuring.\u003c\/p\u003e\u003cp\u003eRuns on hardwired 208\/240V three-phase service at 26 amps maximum draw and a 10,100 W total rating. Water in is 3\/4\" G at 20 ± 5 psi, waste out is 3\/4\" pumped. The cabinet measures 30.1 inches wide by 26.3 inches deep by 57 inches tall, 308 pounds net and 357 pounds crated, running at 59.5 dB(A). Built in Italy, cETL (C-UL-US) listed, UL Classified EPH, Energy Star qualified, one-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143397716126,"sku":"EUR-L25EKDPS3PH","price":12812.71,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_L25ek_CC_SH_f5b96abb-3fa1-462f-aa83-dd9be85fd821.png?v=1789708114"},{"product_id":"lamber-l21eks-high-temp-pass-through-dishwasher-hood-start-29a-single-phase","title":"Lamber L21EKS High-Temp Pass-Through Dishwasher, Hood Start — 29A Single Phase","description":"\u003cp\u003eDrop the hood and the cycle runs. No button, no free hand needed, no rack sitting warm while the dishwasher finishes a phone call — across a few hundred racks a week that single design decision is what separates a dish pit that keeps pace from one that backs up into the aisle. The L21EKS is Lamber's high-temperature pass-through built for that rhythm, on a footprint of 29.75 by 23.75 inches that slots between a soiled table and a clean one.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThermocontrol\u003c\/strong\u003e regulates the sanitizing rinse temperature on every cycle, including through long continuous runs when a lesser machine drifts, and a security thermostat stands behind it. Stainless steel upper and lower wash and rinse arms hit the rack from both directions. The tank is slanted with rounded edges and washes itself down on drain, integral filters catch the soil before it reaches the pump, and the pressed door is self-cleaning — three details that decide how long the closing crew spends on the machine each night. Soft start eases the first pulse of pressure so glassware survives it. Detergent and rinse pumps are built in, the tank fills automatically, and the soft-touch panel shows temperature at a glance. Double-wall thermal insulation keeps the heat in the machine instead of the room, a door safety device stops the cycle if the hood lifts, and the control panel comes out for service without a truck roll.\u003c\/p\u003e\u003cp\u003eDraws 29 amps on single-phase service and drains by gravity to a floor drain beneath the machine. The cabinet stands 56.5 inches tall on a 29.75 x 23.75-inch footprint; dish tables are ordered separately, and drain tempering valves and fitting kits are available. Built in Italy, cETL (C-UL-US) listed, UL EPH classified, Energy Star qualified, with a two-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143399518366,"sku":"EUR-L21EKS","price":9782.89,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/l21ekdps_80a57a95-4ecc-4989-b26e-039c142a7548.jpg?v=1789708115"},{"product_id":"lamber-p700ekdps-pot-and-pan-washer-drain-pump-10-500w-208v-3-phase","title":"Lamber P700EKDPS Pot and Pan Washer, Drain Pump, 10,500W — 208V 3-Phase","description":"\u003cp\u003eA stainless steel wash pump driving stainless upper and lower arms, aimed squarely at the load a dish machine cannot take: braising pans with scorched fond, stock pots, hotel pans, sheet trays. The P700EKDPS washes from above and below at once, which is the only way baked-on soil comes off without a person and a green pad standing over a sink for an hour after service. Ten thousand five hundred watts is what pays for that hour back every night.\u003c\/p\u003e\u003cp\u003eThe tank is slanted with rounded edges and washes itself down on drain, and \u003cstrong\u003etwo integral filters\u003c\/strong\u003e catch the heavy debris a pot load produces before any of it reaches the pump — the failure mode that kills machines put on pot duty without the filtration to match. The door is counterbalanced and double-walled, so it holds position while both of your hands are on a 40-quart pot, and the same double-wall construction handles thermal and acoustic insulation, keeping heat and noise out of a room that already has plenty of both. Digital thermostats on a soft-touch panel show wash and rinse temperature, a security thermostat backs them up, the tank loads automatically, and the frontal control panel opens for service without pulling the machine out of the line.\u003c\/p\u003e\u003cp\u003eRuns on hardwired 208V three-phase service at 10,500 watts and 28 amps. An integrated drain pump discharges waste under pressure, so no floor drain is needed beneath the machine. Footprint is 33.25 inches wide by 31.7 inches deep. Built in Italy, cETL (C-UL-US) listed, UL EPH classified, Energy Star qualified, one-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143401255070,"sku":"EUR-P700EKDPS","price":17891.64,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_P700EKDPS_HiResPicture_LeftSideFull.jpg?v=1786835514"},{"product_id":"lamber-l21ekdps-high-temp-pass-through-dishwasher-drain-pump-29a-single-phase","title":"Lamber L21EKDPS High-Temp Pass-Through Dishwasher, Drain Pump — 29A Single Phase","description":"\u003cp\u003eAn integral drain pump puts this hood machine where the plumbing says no. Waste leaves under pressure instead of falling by gravity, so the L21EKDPS installs against an outside wall, in an island layout, or in a retrofit where cutting the slab for a floor drain was never on the table. Everything else about it is built around the same idea: fewer reasons for the dish pit to stop.\u003c\/p\u003e\u003cp\u003eThe cycle starts when the hood closes — no button, no free hand, no rack waiting. \u003cstrong\u003eThermocontrol\u003c\/strong\u003e regulates the sanitizing rinse temperature on every cycle including long continuous runs, with a security thermostat behind it, and multiple cycle lengths let a cook match the program to the soil instead of running everything at fifteen minutes. Stainless upper and lower wash and rinse arms cover the rack from both sides. The slanted tank has rounded edges and washes itself down on drain, migrating debris to integral filters rather than into a dead corner someone has to reach into at 11 p.m. Soft start eases the first pulse of pressure so glassware survives it, detergent and rinse pumps dose automatically, the tank loads itself, double-wall thermal insulation keeps heat in the machine, and the control panel is removable for service.\u003c\/p\u003e\u003cp\u003eDraws 29 amps on single-phase service. The cabinet stands 56.5 inches tall on a 29.75 x 23.75-inch footprint; dish tables are ordered separately, and drain tempering valves and fitting kits are available. Built in Italy, C-UL-US listed, UL EPH classified, Energy Star qualified, with a \u003cstrong\u003etwo-year warranty\u003c\/strong\u003e.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143403516062,"sku":"EUR-L21EKDPS","price":10891.64,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/l21ekdps.jpg?v=1789708135"},{"product_id":"lamber-p800ek-universal-pot-and-pan-washer-19-7-inch-wash-height-208v-3-phase","title":"Lamber P800EK Universal Pot and Pan Washer, 19.7-Inch Wash Height — 208V 3-Phase","description":"\u003cp\u003eNineteen and seven-tenths inches of wash height. That number is the whole reason this machine exists: stock pots stand upright, sheet pans go in on edge, mixing bowls and utensil racks and full-size hotel pans all clear the arms. Anything a dish machine sends back to the pot sink goes into the P800EK instead, and the labor that used to happen at that sink after service stops happening.\u003c\/p\u003e\u003cp\u003eA stainless steel wash pump feeds upper and lower arms, and a dedicated \u003cstrong\u003ebooster pump\u003c\/strong\u003e holds rinse pressure high enough to strip detergent out of deep vessels — the step that a standard rinse line cannot manage once a container is more than a few inches tall. Three removable filters handle the soil a cookware load produces, the tank bottom is slanted with rounded edges so it washes itself down on drain, and the rack guide lifts out for cleaning. Digital thermostats on a soft-touch panel report wash and rinse temperature, the large handle works with a wet glove, and internal components sit immediately behind the panel so a service call takes minutes instead of an afternoon.\u003c\/p\u003e\u003cp\u003eRuns on hardwired 208V three-phase service at 10,500 watts and 28 amps, draining by gravity to a floor drain beneath the machine; a drain pump is available as an option, as are linear and corner configurations for tight dish rooms. The cabinet measures 33 inches wide by 32 inches deep by 63 inches tall. Built in Italy, cETL (cUL US) listed, UL EPH classified, Energy Star qualified, one-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143406465182,"sku":"EUR-P800EK","price":19641.1,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_P800EK_HiResPicutre_LeftSide.jpg?v=1789708158"},{"product_id":"lamber-l25eks1ph-pass-through-dishwasher-0-6-gal-per-rack-208-240v-single-phase","title":"Lamber L25EKS1PH Pass-Through Dishwasher, 0.6 Gal Per Rack — 208\/240V Single Phase","description":"\u003cp\u003eSix tenths of a gallon of fresh water per rack, out of a machine that runs on single-phase power. Most buildings have 208\/240V single phase and no three-phase service anywhere near the dish room, and that fact alone eliminates a lot of otherwise good dish machines. The L25EKS1PH is the same 57-inch Lamber pass-through cabinet, hardwired to a single-phase supply at 33 amps and a 7,100 W total rating.\u003c\/p\u003e\u003cp\u003eRacks measure 19.6 x 19.6 inches with \u003cstrong\u003e16.3 inches of plate clearance\u003c\/strong\u003e, so dinner plates load upright, glass racks stack and bus tubs go in whole. Four cycles — 2, 3, 4 and 15 minutes — cover the range from a rush of glassware to a pan left soaking overnight, each drawing 0.6 gallons while an 8.9-gallon tank held by a 3,000 W element recirculates the wash. A 6,000 W rinse package and a 2.1-gallon boiler take a 131-140°F supply up to a 180-195°F sanitizing rinse, and Thermocontrol holds that setpoint cycle after cycle rather than letting it sag under a continuous run. Soft start eases the 1,100 W wash pump into the load so glass and light china survive the first pulse; the cycle starts on its own when the hood closes; detergent and rinse-aid pumps dose chemical without anyone measuring.\u003c\/p\u003e\u003cp\u003eHardwired to 208\/240V single-phase service. Water in is 3\/4\" G at 20 ± 5 psi; the 1-1\/4\" gravity outlet needs a floor drain below the machine. The cabinet is 30.1 inches wide by 26.3 inches deep by 57 inches tall, 308 pounds net and 357 pounds crated, running at 59.5 dB(A). Built in Italy, cETL (cUL US) listed, UL EPH classified, Energy Star qualified, one-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143408300190,"sku":"EUR-L25EKS1PH","price":12028.9,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_L25ek_CC_SH_fa8a8cfd-2361-43b0-a47e-83ae3f963400.png?v=1789708165"},{"product_id":"lamber-l25ekdps1ph-pass-through-dishwasher-drain-pump-208-240v-single-phase-33a","title":"Lamber L25EKDPS1PH Pass-Through Dishwasher, Drain Pump — 208\/240V Single Phase, 33A","description":"\u003cp\u003eSingle-phase power and a drain pump — the two install constraints that kill most dish machine specs, solved in one cabinet. The L25EKDPS1PH hardwires to 208\/240V single-phase service at 33 amps, and a 30-watt pump pushes waste out under pressure through a 3\/4-inch line, so the machine does not have to sit over a floor drain. That is a dish room you can lay out around the room rather than around the plumbing.\u003c\/p\u003e\u003cp\u003eFour cycles run 2, 3, 4 and 15 minutes: a two-minute pass for a bar's glass racks, fifteen for a pan that soaked overnight. Each cycle draws \u003cstrong\u003e0.6 gallons\u003c\/strong\u003e of fresh water while an 8.9-gallon tank recirculates the wash, and racks measure 19.6 x 19.6 inches with 16.3 inches of plate clearance, so plates stand upright and bus tubs load whole. A 6,000 W rinse package and a 2.1-gallon boiler take the 131-140°F supply to a 180-195°F sanitizing rinse; Thermocontrol holds that number through a continuous run, which is what turns heat sanitizing into something you can put on an inspection report. Soft start eases the 1,100 W wash pump into the load so glassware survives the first pulse, the cycle begins when the hood closes, and built-in detergent and rinse-aid pumps dose chemical automatically.\u003c\/p\u003e\u003cp\u003eHardwired 208\/240V single phase, 7,100 W total rating, no cord or plug. Water in is 3\/4\" G at 20 ± 5 psi, waste out is 3\/4\" pumped. The cabinet is 30.1 inches wide by 26.3 inches deep by 57 inches tall, 308 pounds net and 357 pounds crated, running at 59.5 dB(A). Built in Italy, cETL (cUL US) listed, UL EPH classified, Energy Star qualified, one-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143410102430,"sku":"EUR-L25EKDPS1PH","price":12629.27,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_L25ek_CC_SH.png?v=1789708173"},{"product_id":"lamber-l21ekdpscv-pass-through-dishwasher-steam-condenser-drain-pump-208-240v","title":"Lamber L21EKDPSCV Pass-Through Dishwasher, Steam Condenser, Drain Pump — 208\/240V","description":"\u003cp\u003eLift the hood and nothing billows out. A steam condenser captures the vapor at the end of each cycle, recovers the heat and puts it back into the next run — which means the plume that normally rolls into the ceiling, fogs the room and drives an exhaust hood requirement simply does not appear. For a dish area without dedicated dish room exhaust, that is the deciding feature, and the recovered heat lowers what the machine costs to run at the same time.\u003c\/p\u003e\u003cp\u003eFour cycles run 2, 3, 4 and 15 minutes across a 19.6 x 19.6-inch rack with \u003cstrong\u003e16.3 inches of plate clearance\u003c\/strong\u003e, from bar glassware to a hotel pan left soaking. Each cycle draws 0.6 gallons of fresh water while an 8.9-gallon tank recirculates the wash, and a 6,000 W rinse package with a 1.3-gallon boiler delivers a 185-195°F sanitizing rinse held by Thermocontrol. Upper and lower rotating wash and rinse arms cover the rack from both directions. An integral 30-watt drain pump discharges waste under pressure through a 3\/4-inch line, so the machine installs without a floor drain beneath it. Double-wall construction keeps the machine under 63 dB(A) and keeps its heat off your cooks.\u003c\/p\u003e\u003cp\u003eHardwired to 208\/240V single-phase service, 6,100-6,700 W total rating at 24-28 amps. Run it on filtered water; reverse osmosis water is not compatible with this machine, and a mixed hot-and-cold supply through an adjustable thermostatic mixing valve is the recommended feed. The cabinet is 26.7 inches wide by 28.5 inches deep by 66.5 inches tall, 262 pounds net and 295 pounds crated. Built in Italy, C-UL-US listed, UL EPH classified, Energy Star qualified, with a \u003cstrong\u003etwo-year warranty\u003c\/strong\u003e.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143414657182,"sku":"EUR-L21EKDPSCV","price":14618.66,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_L21EKDPSCV_HiResPicture_1.png?v=1789708177"},{"product_id":"lamber-f99ekdps-undercounter-dishwasher-30-racks-hr-180-f-rinse-25-5-wide","title":"Lamber F99EKDPS Undercounter Dishwasher — 30 Racks\/hr, 180°F Rinse, 25.5\" Wide","description":"\u003cp\u003eThirty racks an hour out of a machine 25.5 inches wide, and 14.5 inches of clearance inside it. That clearance is the reason to buy this one over a standard undercounter: dinner plates, mixing bowls and tall stemware go through the same door on the same cycle, so the dish pit stops sorting ware into two piles.\u003c\/p\u003e\u003cp\u003eThe final rinse runs at 180 to 195°F, which is how you sanitize with heat instead of buying chemical sanitizer every month, and a 6,000 W rinse element behind a 1.5-gallon boiler is what holds that temperature at thirty racks an hour. Wash cycles run 2, 3 or 4 minutes — 30, 20 or 15 racks per hour — so a bar rush and a plate-heavy dinner service get different treatment from the same machine. The double-rack design lets plates and glasses share a load. Soft start ramps the pump instead of slamming it, cutting detergent and water use, and a 0.6-gallon draw per cycle keeps the water bill honest. Soap and rinse pumps and automatic tank loading are built in, so the crew loads, closes and walks. At under 54 dB it will not compete with the dining room.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHardwired to 208V single-phase service, 6,500 W at 29 A, 60 Hz.\u003c\/strong\u003e A built-in drain pump means it installs where gravity drainage is unavailable. Water inlet is 3\/4\" at 131 to 140°F and 40 to 80 psi. The cabinet measures 25.5 in L x 23.6 in W x 32.2 in H, weighs 158 lb, and takes a 19.6 x 19.6 in rack. The slanted tank self-washes and the control panel lifts out for service. \u003cstrong\u003ecUL US listed, UL EPH certified, Energy Star rated\u003c\/strong\u003e, with a two-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143475376286,"sku":"EUR-F99EKDPS","price":6332.39,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_F99EKDPS_HiResPicture_ControlPanelDetailClosed.jpg?v=1789708284"},{"product_id":"lamber-dsp4ekdps-undercounter-dishwasher-600-dishes-hr-4-cycles-180-f-rinse","title":"Lamber DSP4EKDPS Undercounter Dishwasher — 600 Dishes\/hr, 4 Cycles, 180°F Rinse","description":"\u003cp\u003eSix hundred dishes an hour through a 25.6-inch cabinet, on four selectable cycles. The DSP4EKDPS is the machine that keeps a full dining room in clean plates through a dinner rush without a second unit or a second body in the dish pit, and the fourth cycle — a 15-minute wash — is there for the sheet pans and hotel pans nobody wants to hand-scrub at close.\u003c\/p\u003e\u003cp\u003eThe DPS designation means a top rotating rinse arm, so rinse water sweeps the whole rack from above instead of relying on a fixed spray, and heavily loaded plates come out without shadowed spots. The final rinse runs 180 to 195°F, sanitizing with heat rather than chemical sanitizer, and a thermostatic control system holds both wash and rinse temperature steady across every cycle instead of letting them sag as racks come through. Cycles run 2, 3, 4 or 15 minutes at 30\/20\/15\/4 racks an hour, all from a 19.6 x 19.6 in rack. Automatic tank loading, soft start and integrated soap and rinse pumps take the manual steps out, and a 4-gallon wash tank with 0.6 gallons drawn per cycle keeps water use in check.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHardwired to 208V single-phase, 3,550 W, 60 Hz.\u003c\/strong\u003e The built-in drain pump lets it go in where gravity drainage is unavailable, and the 3\/4\" G inlet takes 131 to 140°F water at 40 to 80 psi. Cabinet is 25.6 in L x 23.7 in W x 32.2 in H with a 15.3-inch work height and 12.6 inches of clearance, weighing 136 lb. Stainless throughout, \u003cstrong\u003ecETL (cUL US) listed, UL EPH certified, Energy Star rated\u003c\/strong\u003e, one-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143477407902,"sku":"EUR-DSP4EKDPS","price":4772.29,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_DPS4EKDPS_HiResPicture_Open_1_2026.png?v=1789708296"},{"product_id":"lamber-f99dyps-undercounter-dishwasher-programmable-controls-180-f-rinse-208v","title":"Lamber F99DYPS Undercounter Dishwasher — Programmable Controls, 180°F Rinse, 208V","description":"\u003cp\u003eA Soft-Touch electronic panel with an interactive display, programmable wash parameters, adjustable rinse-aid dosing and a running cycle counter — this is the undercounter Lamber for an operator who wants the dish machine set once and then left alone. The wash phase shows on the display as it runs, so a manager can see where a cycle is instead of guessing at a closed door.\u003c\/p\u003e\u003cp\u003eThe final rinse runs 180 to 195°F, so sanitizing is done with heat and there is no chemical sanitizer to buy month after month. Upper and lower rotating wash and rinse arms cover the rack from both directions, and the multicycle control lets you program a short bar cycle and a long plate cycle rather than compromising with one. Soft start ramps the pump, soap and rinse pumps meter automatically, and automatic tank loading fills without an operator standing over it. Construction is 18\/10 AISI 304 stainless with double-wall thermal and acoustic insulation and a counterbalanced double-wall door that stays where you put it. The tank is slanted and self-washing with rounded edges, and two integral stainless filters lift out — the closing routine is a rinse and a filter pull, not a scrub.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRuns on 208V single-phase service at 6,500 W with a built-in drain pump\u003c\/strong\u003e, so it installs where gravity drainage is unavailable. The cabinet measures 25.59 in L x 23.62 in W x 32.5 in H and ships with two sets of basket guide rails; the control panel is removable for service. Drain tempering valve and fitting kits are available. Built in Italy, \u003cstrong\u003ecETL (cUL US) listed, UL EPH certified, Energy Star rated\u003c\/strong\u003e, with a two-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48143479898270,"sku":"EUR-F99DYPS","price":6379.19,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/F99-dy-DPS-2022-DG.jpg?v=1786984524"},{"product_id":"lamber-dsp3-high-temperature-glasswasher-3200w-gravity-drain-208v","title":"Lamber DSP3 High-Temperature Glasswasher — 3200W, Gravity Drain, 208V","description":"\u003cp\u003e\u003cstrong\u003eThermocontrol holds the rinse at its target temperature cycle after cycle, including through a five-hour bar rush.\u003c\/strong\u003e That is the spec that separates a glasswasher that sanitizes at 9 p.m. from one that only did it at 5 — most machines let the tank sag as demand stacks up, and the DSP3 is engineered specifically against that. A security thermostat backs it up, and \u003cstrong\u003ewash and rinse thermometers on the panel\u003c\/strong\u003e show your crew exactly where both temperatures sit instead of asking them to trust a light.\u003c\/p\u003e\u003cp\u003eInside, a \u003cstrong\u003estainless steel lower rotating wash arm\u003c\/strong\u003e works with \u003cstrong\u003eupper and lower rotating rinse arms\u003c\/strong\u003e, so glasses get hit from below and above on every revolution — no shadowed rack corners and no second run for the tall pilsners. \u003cstrong\u003eAutomatic tank loading\u003c\/strong\u003e fills the machine on its own between cycles, \u003cstrong\u003esoap and rinse pumps\u003c\/strong\u003e dose chemical without a hand in the tank, and a \u003cstrong\u003edoor safety device\u003c\/strong\u003e stops the cycle if the door opens mid-run. When something needs service, the \u003cstrong\u003econtrol panel comes out\u003c\/strong\u003e rather than requiring the machine to come out from under the counter.\u003c\/p\u003e\u003cp\u003eThe DSP3 draws \u003cstrong\u003e3,200 watts at 15 amps on 208V single-phase\u003c\/strong\u003e service and uses a \u003cstrong\u003egravity drain\u003c\/strong\u003e, so it wants a floor drain below the outlet height — the DSP3DPS is the pump-drain version if your bar does not have one. It measures \u003cstrong\u003e20\" deep x 18\" wide x 29.25\" tall\u003c\/strong\u003e for an undercounter install, is built in \u003cstrong\u003eItaly\u003c\/strong\u003e, and carries \u003cstrong\u003ecUL US listing and UL EPH classification\u003c\/strong\u003e with a 1-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48150864101534,"sku":"EUR-DSP3","price":4213.34,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_DSP3_HiResPicture_LeftSide.jpg?v=1789708440"},{"product_id":"lamber-dsp3dps-glasswasher-16-rack-180-195-f-rinse-drain-pump-208v","title":"Lamber DSP3DPS Glasswasher — 16\" Rack, 180-195°F Rinse, Drain Pump, 208V","description":"\u003cp\u003e\u003cstrong\u003eThe final rinse lands between 180°F and 195°F, every cycle.\u003c\/strong\u003e That is hot enough to sanitize with water alone, so your bar stops buying chemical sanitizer by the case and your glasses come out clear instead of filmed. The DSP3DPS runs a \u003cstrong\u003e16\" x 16\" rack\u003c\/strong\u003e with \u003cstrong\u003e11.8\" of clearance\u003c\/strong\u003e — pint glasses, stemware, and shaker tins upright, plus plates and small pans when the dish pit gets buried — from a cabinet \u003cstrong\u003e19.9\" deep x 18.1\" wide x 29.2\" tall\u003c\/strong\u003e that slides under a standard back-bar counter.\u003c\/p\u003e\u003cp\u003eWater use is where it pays for itself: \u003cstrong\u003e0.6 gallons per cycle\u003c\/strong\u003e, 19 gallons an hour flat out. A \u003cstrong\u003e200-watt wash pump moves 42 gallons per minute\u003c\/strong\u003e through a lower rotating wash arm, a rotating rinse arm, and a fixed upper spray arm, so the chamber gets scrubbed from three directions instead of one — that is what clears lipstick and beer film without a pre-scrub. \u003cstrong\u003eThermostatic control holds wash and rinse temperature\u003c\/strong\u003e for the length of the cycle rather than letting the tank sag as the night goes on, and the \u003cstrong\u003erinse aid dispenser and detergent pump with automatic tank filling\u003c\/strong\u003e mean your closing crew is not dosing chemicals by hand. It runs under \u003cstrong\u003e70 dB\u003c\/strong\u003e, which matters when the machine sits eight feet from a guest.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eThe built-in drain pump is the reason to choose this one over the gravity-drain DSP3\u003c\/strong\u003e — it pushes waste water up and out, so the machine can go where the floor drain is not. Plan \u003cstrong\u003e208V single-phase 60 Hz on a NEMA 6-20P receptacle\u003c\/strong\u003e, a \u003cstrong\u003e3\/4\" water inlet at 40 to 80 psi\u003c\/strong\u003e, and a \u003cstrong\u003e3\/4\" outlet\u003c\/strong\u003e. It holds a 5.2-gallon tank, weighs 95 lb, is built in \u003cstrong\u003eItaly\u003c\/strong\u003e, and carries \u003cstrong\u003eC-UL-US listing and UL Classified EPH\u003c\/strong\u003e with a 1-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48150864167070,"sku":"EUR-DSP3DPS","price":4751.31,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_DPS3DPS_HiResPicture1.jpg?v=1789708441"},{"product_id":"lamber-s480ekdps-glasswasher-multicycle-drain-pump-energy-star","title":"Lamber S480EKDPS Glasswasher — Multicycle, Drain Pump, Energy Star","description":"\u003cp\u003e\u003cstrong\u003eEnergy Star qualified and double-wall insulated — the only glasswasher in the Lamber DSP line carrying both.\u003c\/strong\u003e The insulation is doing two jobs at once: it keeps tank heat inside the cabinet so the elements cycle less, which is what earns the Energy Star badge, and it keeps that heat out of your bar, where every degree the machine sheds is a degree your air conditioning has to remove. On a back bar in July, a quiet, cool-running machine is worth more than a spec sheet suggests.\u003c\/p\u003e\u003cp\u003eThis is the \u003cstrong\u003eDeluxe multicycle\u003c\/strong\u003e model, so cycle length matches the load — a fast pass for lightly used pint glasses, a longer one for stemware with lipstick or for plates that landed in the bar. A \u003cstrong\u003esoft-touch electronic control panel displays the temperature\u003c\/strong\u003e, so nobody has to guess whether the machine is up to sanitizing heat, and \u003cstrong\u003esoft start\u003c\/strong\u003e ramps the wash pump instead of slamming it, which keeps stemware from chattering in the rack and takes the shock off the drivetrain. \u003cstrong\u003eThermocontrol\u003c\/strong\u003e holds the rinse at its target through long continuous runs, with a security thermostat behind it.\u003c\/p\u003e\u003cp\u003eWater is moved by a \u003cstrong\u003estainless steel lower rotating wash arm\u003c\/strong\u003e and \u003cstrong\u003eupper and lower rotating rinse arms\u003c\/strong\u003e, fed by soap and rinse pumps with \u003cstrong\u003eautomatic tank loading\u003c\/strong\u003e. A \u003cstrong\u003ebuilt-in drain pump\u003c\/strong\u003e pushes waste water up and out, so you are not limited to a spot with a floor drain below the outlet. A door safety device stops the cycle if the door opens, and the control panel is removable for service without pulling the machine. It runs on \u003cstrong\u003esingle-phase service at 15 amps\u003c\/strong\u003e, fits an undercounter opening at \u003cstrong\u003e20\" deep x 19\" wide x 29.25\" tall\u003c\/strong\u003e, and is built in \u003cstrong\u003eItaly\u003c\/strong\u003e with \u003cstrong\u003eC-UL-US listing, UL Classified EPH, and Energy Star\u003c\/strong\u003e, plus a 1-year warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48150864199838,"sku":"EUR-S480EKDPS","price":5648.63,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/LAMBER_S480EKDPS_HiResPicture_LeftSideOpen.jpg?v=1789708443"},{"product_id":"lamber-ac00027-stainless-steel-dishwasher-base-22-in-tall-fits-dsp3-and-s480-dishwashers","title":"Lamber AC00027 Stainless Steel Dishwasher Base, 22 in Tall — Fits DSP3 and S480 Dishwashers","description":"\u003cp\u003eLamber AC00027 is the stainless steel base built for the DSP3 and S480 undercounter dishwashers (DSP3DPS, S480EKDPS). It lifts the machine 22 inches off the floor so the door and rack sit at working height instead of forcing staff to bend over a low counter for every load — and the open compartment underneath swallows the spare racks and the bottle of detergent that would otherwise live on the floor.\u003c\/p\u003e\u003cp\u003eBuilt from AISI 304 18\/10 stainless steel at 18 x 18 inches square and 20 pounds, it is a wash-down fixture, not a shelf: the same grade of steel as the dishwasher it carries, ready for a wet floor and a daily hose-out. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253680255134,"sku":"EUR-AC00027","price":971.03,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/Lamber-Base-For-Dishwasher-Model-DPS3-And-S480-AC00027.jpg?v=1791293998"},{"product_id":"lamber-cc00019-open-cup-and-glass-rack-19-75-in-fits-20-x-20-in-dishwashers","title":"Lamber CC00019 Open Cup and Glass Rack, 19.75 in — Fits 20 x 20 in Dishwashers","description":"\u003cp\u003eLamber CC00019 is the full-size 19.75 x 19.75 in open rack for Lamber's 20 x 20 inch dishwashers — the L21, L25, F99 and DSP4 machines (DSP4EKDPS, F99DYPS, F99EKDPS, L21EKDPS, L21EKS, L25EKDPS1PH, L25EKDPS3PH, L25EKS1PH and L25EKS3PH). Lamber's own code for it is CB, the cups-and-glasses rack: an undivided open bottom rather than a compartment grid, so it takes whatever mix of cups, mugs and glasses the bar hands you instead of one glass shape.\u003c\/p\u003e\u003cp\u003eAt 4 inches deep it is the low-profile rack in the family, which is what makes it work for cups and short glassware. Plastic, 7 lbs, made in Italy, and the open construction lets wash water hit every surface and lets everything drain and dry on the rack. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253696311454,"sku":"EUR-CC00019","price":109.21,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00019-CB-tazze-bicchi.jpg?v=1788984760"},{"product_id":"lamber-cc00024-peg-rack-for-plates-12-to-16-plates-fits-20-x-20-in-dishwashers","title":"Lamber CC00024 Peg Rack for Plates, 12 to 16 Plates — Fits 20 x 20 in Dishwashers","description":"\u003cp\u003eLamber CC00024 is the peg rack that turns a 20 x 20 inch Lamber dishwasher into a plate machine. Pegs hold each plate upright and separated so the wash arms reach both faces and nothing nests, chips or comes out with a wet ring — 12 to 16 plates a cycle, which is a full service station's worth per load.\u003c\/p\u003e\u003cp\u003eIt fits the 20 x 20 in Lamber dishwasher family: DSP4EKDPS, F99DYPS, F99EKDPS, L21EKDPS, L21EKS, L25EKDPS1PH, L25EKDPS3PH, L25EKS1PH and L25EKS3PH. Moulded plastic, made in Italy. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253696376990,"sku":"EUR-CC00024","price":109.21,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00019-CB-tazze-bicchi_9470d686-895d-4672-a7b8-177e22b7cb9a.jpg?v=1788984761"},{"product_id":"lamber-cc00043-cutlery-basket-8-compartments-fits-all-lamber-dishwashers","title":"Lamber CC00043 Cutlery Basket, 8 Compartments — Fits All Lamber Dishwashers","description":"\u003cp\u003eLamber CC00043 is the cutlery basket for Lamber commercial dishwashers — eight compartments in two rows of four, each 3.25 x 3.25 inches. Splitting cutlery eight ways is what stops knives, forks and spoons from shielding each other in the wash, and it is also what lets the dish porter sort straight into the drawer instead of picking through one heaped pile.\u003c\/p\u003e\u003cp\u003eIt fits across the Lamber dishwasher range, including the F99, L21 and L25 machines (F99DYPS, F99EKDPS, L21EKDPS, L21EKS, L25EKDPS1PH, L25EKDPS3PH, L25EKS1PH and L25EKS3PH). Sold individually — one basket per order. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253696409758,"sku":"EUR-CC00043","price":94.68,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00019-CB-tazze-bicchi_2e3f78f5-d54b-4a8e-9d40-a0c05d80b509.jpg?v=1788984761"},{"product_id":"lamber-cc00045-cutlery-insert-fits-dsp3-and-s480-dishwashers","title":"Lamber CC00045 Cutlery Insert — Fits DSP3 and S480 Dishwashers","description":"\u003cp\u003eLamber CC00045 is the cutlery insert for the DSP3 and S480 dishwashers (DSP3DPS, S480EKDPS). It gives cutlery a dedicated pocket in the rack instead of letting it lie flat and shadow itself, so knives, forks and spoons stand where the wash arms can reach them and come out of the machine already grouped for the drawer.\u003c\/p\u003e\u003cp\u003eMoulded plastic, 4.5 in high by 4.5 in long by 5 in wide, 1 lb — a small, light part that lives in the rack and takes the same wash cycle as everything else in it. Made in Italy. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253696442526,"sku":"EUR-CC00045","price":10.22,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00045-1.jpg?v=1791295365"},{"product_id":"lamber-cc00049-saucer-rack-insert-10-sections-fits-all-lamber-dishwashers","title":"Lamber CC00049 Saucer Rack Insert, 10 Sections — Fits All Lamber Dishwashers","description":"\u003cp\u003eLamber CC00049 is the ten-section saucer insert that sits inside a full Lamber dishwasher rack. Each saucer stands in its own slot rather than stacking, which is the only way a saucer gets washed on both faces and comes out dry — ten per insert, and you can run more than one insert in a rack alongside other loads.\u003c\/p\u003e\u003cp\u003eIt measures 14.25 in long by 3.75 in wide by 3.25 in high and weighs 2 lbs, so it is a narrow divider, not a standalone 20 in rack. Fits across the Lamber dishwasher range including the DSP3, F99, L21, L25 and S480 machines. Sold individually — one insert per order. Made in Italy. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253696475294,"sku":"EUR-CC00049","price":16.67,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/section-rack-for-saucer-for-restaurant-commercial-dishwashers-cc00049.jpg?v=1789748343"},{"product_id":"lamber-cc00052-open-glass-rack-15-5-in-with-6-in-depth-fits-dsp3-and-s480-glasswashers","title":"Lamber CC00052 Open Glass Rack, 15.5 in with 6 in Depth — Fits DSP3 and S480 Glasswashers","description":"\u003cp\u003eLamber CC00052 is the compact 15.5 x 15.5 in open rack for the DSP3 and S480 glasswashers (DSP3DPS, S480EKDPS) — the 16 x 16 inch machines, not the 20 inch dishwashers. Read the two numbers before you order: 15.5 inches square is the small glasswasher footprint, and the 6 inch depth is the deepest in this rack family, which is what makes it the one for tall stemware and highball glasses.\u003c\/p\u003e\u003cp\u003eThe open, undivided construction means no fixed glass size — wash water reaches every surface and the load drains and dries on the rack. Plastic, 4 lbs, made in Italy. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253696508062,"sku":"EUR-CC00052","price":66.71,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00089-CLP52-P550.jpg?v=1788984761"},{"product_id":"lamber-cc00059-stainless-steel-counterbalance-for-cups-and-glasses-fits-20-x-20-in-lamber-dishwashers","title":"Lamber CC00059 Stainless Steel Counterbalance for Cups and Glasses — Fits 20 x 20 in Lamber Dishwashers","description":"\u003cp\u003eLamber CC00059 is the stainless steel hold-down grid for 20 x 20 inch Lamber dishwashers. It does the opposite job to a rack: laid over a load of cups, glasses and other light containers, its weight keeps them from lifting, flipping and filling with dirty water when the wash arms hit them — the single most common cause of a rewash on a bar load.\u003c\/p\u003e\u003cp\u003eStainless steel, 4 inches high and 4 lbs, made in Italy — the only stainless item in Lamber's rack accessory line, and heavy enough to do its job while still lifting off one-handed. It fits the 20 x 20 in family: DSP4EKDPS, F99DYPS, F99EKDPS, L21EKDPS, L21EKS, L25EKDPS1PH, L25EKDPS3PH, L25EKS1PH and L25EKS3PH and P700EKDPS. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253696540830,"sku":"EUR-CC00059","price":78.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00059-CT45.jpg?v=1788984761"},{"product_id":"lamber-cc00064-gastronorm-pan-rack-holds-8-pans-fits-20-x-20-in-dishwashers","title":"Lamber CC00064 Gastronorm Pan Rack, Holds 8 Pans — Fits 20 x 20 in Dishwashers","description":"\u003cp\u003eLamber CC00064 holds up to eight gastronorm pans on edge in a single 20 x 20 inch dishwasher load. Standing pans upright and separated is what gets wash water onto both faces and lets them drain instead of pooling — and it means the whole prep line's pans go through in one cycle rather than three.\u003c\/p\u003e\u003cp\u003eThe rack is 19.75 x 19.75 in with a 4.25 in profile and weighs 8 lbs, so it also works as a carrier: load pans at the sink, wash, then move the rack to the shelf without touching them again. Moulded plastic, made in Italy, and it fits the 20 x 20 in Lamber family — DSP4EKDPS, F99DYPS, F99EKDPS, L21EKDPS, L21EKS, L25EKDPS1PH, L25EKDPS3PH, L25EKS1PH and L25EKS3PH. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704405150,"sku":"EUR-CC00064","price":164.62,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/Lamber-Plastic-Rack-For-8-Gastro-Pans-CC00064.webp?v=1791295223"},{"product_id":"lamber-cc00075-inclined-glass-rack-4-open-rows-fits-16-x-16-in-glasswashers","title":"Lamber CC00075 Inclined Glass Rack, 4 Open Rows — Fits 16 x 16 in Glasswashers","description":"\u003cp\u003eLamber CC00075 is the inclined glass rack for 16 x 16 inch glasswashers, including the DSP3 and S480 machines (DSP3DPS, S480EKDPS). The incline is the whole point: glasses sit at an angle across four open rows so water runs off the base instead of pooling in it, which is the difference between glasses that come out of the machine ready for the bar and glasses that need a towel.\u003c\/p\u003e\u003cp\u003eBuilt in coated stainless steel at 15.75 x 15.75 in with a 6.5 in profile and 5 lbs — steel structure for a rack that gets loaded and carried all night, with the coating protecting the glass rims. Four open rows take a range of glass shapes rather than one fixed size. Made in Italy. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704437918,"sku":"EUR-CC00075","price":156.01,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00075-CA-40.jpg?v=1788985073"},{"product_id":"lamber-cc00090-stainless-steel-open-rack-25-x-26-5-in-fits-p700-dishwashers","title":"Lamber CC00090 Stainless Steel Open Rack, 25 x 26.5 in — Fits P700 Dishwashers","description":"\u003cp\u003eLamber CC00090 is the stainless steel open rack for the P700 rack-conveyor dishwasher (P700EKDPS). At 25 x 26.5 inches it is the machine's full rack size, and it is undivided — no compartments — so it takes trays, sheet pans, oversized dishware and mixed loads that no compartment rack would accept.\u003c\/p\u003e\u003cp\u003eAISI 304 18\/10 stainless steel throughout, 6.5 inches high and 18 lbs. That is a substantial rack, and deliberately so: on a conveyor machine the rack is loaded, pushed, pulled and stacked hundreds of times a day, and stainless is what survives it. Made in Italy. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704470686,"sku":"EUR-CC00090","price":972.64,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00090-CLP64-P700_9e7288f2-4e71-4d27-bb59-4ba415f6229c.jpg?v=1791295303"},{"product_id":"lamber-cc00121-glass-rack-9-compartments-at-5-x-5-in-fits-16-x-16-in-glasswashers","title":"Lamber CC00121 Glass Rack, 9 Compartments at 5 x 5 in — Fits 16 x 16 in Glasswashers","description":"\u003cp\u003eLamber CC00121 holds nine glasses in a 3 x 3 grid, and the number that decides whether it is the right rack is the compartment size: 5 x 5 inches, the widest in Lamber's CC00121 family. Nine large compartments rather than sixteen or twenty-five small ones is the trade you make for wide-bowled glassware — goblets, balloon stemware, oversized tumblers — that will not drop into a 3 or 4 inch cell.\u003c\/p\u003e\u003cp\u003eThe rack is 15.5 x 15.5 in for 16 x 16 inch glasswashers, including the DSP3 and S480 machines (DSP3DPS, S480EKDPS), and stands 7.5 inches high to clear tall glasses. Moulded plastic, 5 lbs, made in Italy. Molded in Italy and covered by Lamber's 90-day warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704503454,"sku":"EUR-CC00121","price":215.72,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00121-LB109.jpg?v=1788985073"},{"product_id":"lamber-cc00123-glass-rack-16-compartments-7-5-in-tall-fits-16-x-16-in-glasswashers","title":"Lamber CC00123 Glass Rack, 16 Compartments, 7.5 in Tall — Fits 16 x 16 in Glasswashers","description":"\u003cp\u003eThe CC00123 is the short 16-glass rack in Lamber's compartment family: four rows of four, each cell 3.75 x 3.75 in, in a 15.5 x 15.5 in footprint that drops straight into any 16 x 16 in glasswasher. At 7.5 in tall it is built for stemless tumblers, rocks glasses and short beer glasses — the profile that lets a bar wash the most units per cycle.\u003c\/p\u003e\u003cp\u003eMolded plastic walls keep every glass upright and separated through the wash and rinse, so rims never touch and breakage stops at the rack. It carries the manufacturer's H160 height code, which is what separates it from the taller CC00125.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704536222,"sku":"EUR-CC00123","price":213.03,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00123-LB216.jpg?v=1788985074"},{"product_id":"lamber-cc00125-tall-glass-rack-16-compartments-10-5-in-tall-fits-16-x-16-in-glasswashers","title":"Lamber CC00125 Tall Glass Rack, 16 Compartments, 10.5 in Tall — Fits 16 x 16 in Glasswashers","description":"\u003cp\u003eThe CC00125 is the tall 16-glass rack — 10.5 in of compartment wall and roomier 4 x 4 in cells, so wine glasses, pilsners and tall highballs are supported near the rim instead of rattling free above a short divider. Four rows of four in the standard 15.5 x 15.5 in footprint for 16 x 16 in glasswashers.\u003c\/p\u003e\u003cp\u003eThis is the H240 build in Lamber's height range, three inches taller than the CC00123 and with a wider cell to match. Choose it when the glassware is stemmed or long, and keep the short rack for tumblers.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704568990,"sku":"EUR-CC00125","price":253.38,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00125_jpg.jpg?v=1788985075"},{"product_id":"lamber-cc00127-glass-rack-25-compartments-7-5-in-tall-fits-16-x-16-in-glasswashers","title":"Lamber CC00127 Glass Rack, 25 Compartments, 7.5 in Tall — Fits 16 x 16 in Glasswashers","description":"\u003cp\u003eTwenty-five glasses in one pass. The CC00127 packs five rows of five into the same 15.5 x 15.5 in footprint as the 16-glass racks, with tight 3 x 3 in cells built for shot glasses, narrow tumblers and juice glasses — the highest-density rack in the Lamber compartment family.\u003c\/p\u003e\u003cp\u003eThe 7.5 in wall height keeps the rack low and easy to lift when loaded, and separates it from the 10 in CC00128, which shares the same 5 x 5 layout for taller glasses. Molded plastic, made in Italy, for any 16 x 16 in glasswasher.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704601758,"sku":"EUR-CC00127","price":221.64,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00127-LB225.jpg?v=1788985074"},{"product_id":"lamber-cc00128-tall-glass-rack-25-compartments-10-in-tall-fits-s480-and-16-x-16-in-glasswashers","title":"Lamber CC00128 Tall Glass Rack, 25 Compartments, 10 in Tall — Fits S480 and 16 x 16 in Glasswashers","description":"\u003cp\u003eSame 25-glass density as the CC00127, three inches more wall. The CC00128 runs five rows of five 3 x 3 in cells at a full 10 in tall, so narrow tall glassware — collins glasses, tall tumblers, flutes — stays braced high on the glass instead of pivoting on a low divider.\u003c\/p\u003e\u003cp\u003eIt loads into 16 x 16 in glasswashers on a 15.5 x 15.5 in footprint and is named on the page for the Lamber S480. Reach for this one when the glasses are tall and thin; the 7.5 in CC00127 handles the short ones.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704634526,"sku":"EUR-CC00128","price":274.9,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00128.jpg?v=1788985074"},{"product_id":"lamber-cc00130-open-glass-rack-no-dividers-9-in-tall-fits-16-x-16-in-glasswashers","title":"Lamber CC00130 Open Glass Rack, No Dividers, 9 in Tall — Fits 16 x 16 in Glasswashers","description":"\u003cp\u003eThe open alternative to Lamber's compartment racks. With no dividers, the CC00130 takes whatever the compartment racks will not — oversized pitchers, mixing tins, odd-shaped barware and mixed loads that never fit a fixed grid. The 9 in perimeter wall keeps the load contained on a standard 15.5 x 15.5 in footprint for 16 x 16 in glasswashers.\u003c\/p\u003e\u003cp\u003eOne rack covers the exceptions, so a bar does not need a second compartment size for the handful of items that will not sit in a cell. Made in Italy, 5 lb.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":48253704667294,"sku":"EUR-CC00130","price":124.81,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/CC00090-CLP64-P700.jpg?v=1788985075"},{"product_id":"lamber-dsp4dps-high-temp-undercounter-dishwasher-with-drain-pump-30-racks-hr-208v-single-cycle","title":"Lamber DSP4DPS High-Temp Undercounter Dishwasher with Drain Pump, 30 Racks\/hr — 208V, Single Cycle","description":"\u003cp\u003eThirty racks an hour off one button, in a cabinet 23.7 inches wide. The Lamber DSP4DPS runs a single two-minute wash-and-rinse cycle and nothing else, so whoever is on dish presses start, pulls the rack two minutes later and loads the next one, with no cycle menu to second-guess in the middle of a rush. For a bar, cafe or small dining room that washes the same plates and glasses all night, that one fast cycle is the whole job.\u003c\/p\u003e\u003cp\u003eSanitizing is done with heat, not chemicals. A 1.32-gallon booster with a 3,000 W element brings the final rinse to 180–195°F on every rack, and the thermostatic control holds the rinse back until the water is up to temperature, so a rack never leaves the machine under-rinsed because the line was moving fast. Stainless rotating wash arms work the 19.6-inch rack from above and below, and a rotating lower rinse arm with a fixed upper arm finishes it. Each cycle draws 0.6 gallons, built-in detergent and rinse-aid pumps meter chemistry automatically, and the tank refills itself.\u003c\/p\u003e\u003cp\u003eThe built-in drain pump is what makes it easy to place. It lifts wastewater up to 24 inches off the floor, so the machine goes in under a counter where there is no floor drain, and at close it empties the tank on its own. The DSP4DPS and its sibling, the Lamber DSP4EKDPS, share the same cabinet, booster and drain pump. The difference is control: the DSP4EKDPS adds an electronic panel with four cycles, including a 15-minute pan cycle. Choose the DSP4DPS when your loads are plates, cups and glassware and you want a dish machine with one button and nothing else to set.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHardwired to 208V single-phase, 3,550 W, 17 A.\u003c\/strong\u003e Connect a 3\/4-inch G water inlet supplying 131–140°F water at 40–80 psi. The cabinet is 23.7 inches wide, 25.6 inches deep and 32.2 inches tall, with a 12.6-inch door opening and 136 pounds of stainless steel. Built in Italy. cULus listed, UL EPH classified to NSF\/ANSI 3 and ENERGY STAR certified, with a 1-year parts and labor warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":67821550043294,"sku":"EUR-DSP4DPS","price":4772.29,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/161051.jpg?v=1793098463"},{"product_id":"lamber-ac00692-rail-kit-for-lamber-f99-undercounter-dishwashers","title":"Lamber AC00692 Rail Kit — for Lamber F99 Undercounter Dishwashers","description":"\u003cp\u003eThe Lamber AC00692 is the factory kit of rails for the Lamber F99 undercounter dishwasher, the deluxe high-temperature machine sold on our site as the F99EKDPS and F99DYPS. Order it to replace damaged rails or to complete an F99 install with the matching Lamber hardware.\u003c\/p\u003e\u003cp\u003eThe kit ships as a pair of slotted metal rails with their mounting screws, so you have everything for both sides in one order rather than sourcing fasteners separately. Using the matched Lamber part keeps the machine's fit and alignment exactly as the factory designed it.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":67821924778142,"sku":"EUR-AC00692","price":146.86,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/Lamber-Kit-Of-Rails-For-F99-Undercounter-Dishwasher-AC00692.jpg?v=1793037928"},{"product_id":"lamber-0400367-basket-support-for-corner-installation-for-lamber-l21-and-l25-pass-through-dishwashers","title":"Lamber 0400367 Basket Support for Corner Installation — for Lamber L21 and L25 Pass-Through Dishwashers","description":"\u003cp\u003eCorner installs put a Lamber pass-through dishwasher at a right angle to the dish table, and racks have to make the turn without hanging up. The 0400367 is the basket support Lamber makes for exactly that layout on the L21 and L25 pass-through dishwashers: it carries the rack at the corner so baskets stay aligned and travel smoothly into and out of the machine.\u003c\/p\u003e\u003cp\u003eOn our site that covers the L21EKS, L21EKDPS and L21EKDPSCV and the L25EKS and L25EKDPS in single- and three-phase. Order it with the machine when you are planning a corner layout, or as a replacement when the original is bent or missing and racks start catching.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":67821933166750,"sku":"EUR-0400367","price":90.38,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/400367.jpg?v=1793037971"},{"product_id":"lamber-ac00005-stainless-steel-dishwasher-base-open-22-in-tall-for-lamber-f99-undercounter-dishwashers","title":"Lamber AC00005 Stainless Steel Dishwasher Base, Open, 22 in Tall — for Lamber F99 Undercounter Dishwashers","description":"\u003cp\u003eLift a Lamber F99 undercounter dishwasher 22 inches off the floor and the dish crew loads and unloads at counter height instead of bending to the floor all shift. The AC00005 is Lamber's open AISI 304 stainless steel base for the F99EKDPS and F99DYPS, with an open lower compartment for spare racks and cleaning products.\u003c\/p\u003e\u003cp\u003eThe base is 18\/10 AISI 304 stainless steel, 23.75 inches wide by 23.75 inches deep, which lines up under the F99's footprint, and weighs 27 pounds. The open front puts spare racks and chemicals within reach of the operator without walking to a storage room.\u003c\/p\u003e\u003cp\u003eMeasures 23.75 inches wide by 23.75 inches deep by 22 inches high. Made in Italy by Lamber, with a 3-month warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":67821938213022,"sku":"EUR-AC00005","price":971.03,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/AC00005-BL-50x50.jpg?v=1793099121"},{"product_id":"lamber-ac00005d-stainless-steel-dishwasher-base-with-door-22-in-tall-for-lamber-f99-undercounter-dishwashers","title":"Lamber AC00005D Stainless Steel Dishwasher Base with Door, 22 in Tall — for Lamber F99 Undercounter Dishwashers","description":"\u003cp\u003eLift a Lamber F99 undercounter dishwasher 22 inches off the floor and the dish crew loads and unloads at counter height instead of bending to the floor all shift. The AC00005D is Lamber's AISI 304 stainless steel base for the F99EKDPS and F99DYPS, with a door that closes off the space underneath for detergent, rinse aid and spare racks.\u003c\/p\u003e\u003cp\u003eThe base is 18\/10 AISI 304 stainless steel, 23.75 inches wide by 23.75 inches deep, which lines up under the F99's footprint, and weighs 32 pounds. The door keeps chemicals out of sight and out of the splash zone, which keeps the dish area tidy for inspection.\u003c\/p\u003e\u003cp\u003eMeasures 23.75 inches wide by 23.75 inches deep by 22 inches high. Made in Italy by Lamber, with a 3-month warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":67821944078494,"sku":"EUR-AC00005D","price":1512.76,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/AC00005-D.jpg?v=1793099215"},{"product_id":"lamber-ac00059-stainless-steel-baking-pan-rack-holds-3-pans-for-lamber-p700-and-p800-pot-washers","title":"Lamber AC00059 Stainless Steel Baking Pan Rack, Holds 3 Pans — for Lamber P700 and P800 Pot Washers","description":"\u003cp\u003eSheet pans and baking trays are the hardest thing to wash well in a basket. They lie flat, block the spray and come out with baked-on corners. The Lamber AC00059 stands up to three baking pans on edge in a stainless steel rack, so the wash arms hit both faces of every pan. It is listed for the Lamber P700EKDPS pot and pan washer and comes in the accessory list for the P800EK universal washer.\u003c\/p\u003e\u003cp\u003eThe rack is stainless steel, 10 inches wide, 17.75 inches deep and 9 inches tall, and weighs 5 pounds. It holds the pans apart so they cannot nest or rattle against each other through the cycle, which protects nonstick and aluminum pans as well as the machine. Made in Italy by Lamber, with a 3-month warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":67821949943966,"sku":"EUR-AC00059","price":189.36,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/AC00059.jpg?v=1793038117"},{"product_id":"lamber-cc00089-stainless-steel-open-rack-20-25-x-22-75-in-for-lamber-p550ek-pot-washers","title":"Lamber CC00089 Stainless Steel Open Rack, 20.25 x 22.75 in — for Lamber P550EK Pot Washers","description":"\u003cp\u003ePots, pans, mixing bowls and utensils go straight into an open rack and come out washed, with nothing in the way of the spray. The Lamber CC00089 is the AISI 304 stainless steel open rack made for the Lamber P550EK pot and pan washer, sized at 20.25 by 22.75 inches to fill its wash chamber.\u003c\/p\u003e\u003cp\u003eStainless steel stands up to the heat, the weight of heavy cookware and the strong detergents of a pot washer far longer than a plastic rack. The open wire design lets water reach every surface and drain cleanly, so items come out ready to dry.\u003c\/p\u003e\u003cp\u003eMeasures 20.25 inches wide by 22.75 inches deep by 6.75 inches high and weighs 13 pounds. Made in Italy by Lamber, with a 3-month warranty.\u003c\/p\u003e","brand":"Lamber","offers":[{"title":"Default Title","offer_id":67821958922398,"sku":"EUR-CC00089","price":882.8,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/files\/Lamber-Stainless-Steel-Rack-for-P550EK-CC00089.jpg?v=1793038165"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0787\/0460\/7390\/collections\/logo-lamber.png?v=1790706503","url":"https:\/\/directfoodequipment.com\/collections\/lamber.oembed","provider":"Direct Food Equipment","version":"1.0","type":"link"}