This commercial griddle buying guide comes down to four decisions, made in this order: fuel (gas or electric, set by the utilities you already have), controls (manual valves or thermostats, set by who is cooking and how consistent the menu has to be), plate (thickness and surface material, set by how hard you load it and what you cook on it), and size (width and depth, set by your peak-hour volume). Get the first two right and the last two are easy. If you are fitting out a whole line, check the griddle against the rest of your list in our commercial kitchen equipment checklist for opening a restaurant.
Commercial Griddle Buying Guide: The Quick Decision Table
Use this table to narrow the field before you compare individual models.
| If your kitchen… | Start with | Why |
|---|---|---|
| Has gas at the line and experienced cooks | Manual gas griddle, 1-inch steel plate | Simplest controls, fewest parts to fail, strong heat for searing |
| Runs written recipe temperatures or high staff turnover | Thermostatic gas griddle | Each zone holds a set temperature, so results do not depend on the cook |
| Has no gas service, or is in a mall, airport or food hall | Thermostatic electric griddle | No gas line; check amperage and phase before you order |
| Cooks eggs, fish, crepes and onions on one plate | Chrome-surface griddle | Less flavor carryover and less heat thrown at the cook |
| Drops large loads of frozen product at peak | Thick plate (1 inch) or a composite plate, deeper cooking surface | More stored heat, so the plate recovers instead of stalling |
| Does light, occasional griddle work | Countertop griddle with a 3/4-inch plate, 24 to 36 inches | Faster heat-up and lower weight on the counter |
Gas vs Electric Griddle: Let Your Utilities Decide First
The building usually settles the gas vs electric griddle question. A new gas line or a panel upgrade can cost more than the griddle, so check the utilities at your line first.
Gas griddles
- Heat: gas models are rated in BTU per hour, typically one burner for every 12 inches of plate. On the units we carry, burner ratings run from about 25,000 to 30,000 BTU/hr each, so a 36-inch griddle lands somewhere around 75,000 to 90,000 BTU/hr in total.
- Fuel type: most ship for natural gas and can be converted to propane. Some include the LP kit in the box; others must be ordered for a specific gas. Conversion is work for a licensed gas fitter, done under the National Fuel Gas Code (NFPA 54) and local code in the US, or the CSA B149.1 Natural Gas and Propane Installation Code in Canada.
- Altitude and pilots: specify your altitude if the spec sheet asks for it. Many models use a standing pilot and need no electrical connection.
Electric griddles
- Power: rated in kilowatts. A full-size 36-inch electric griddle draws a lot of current, and the phase matters. For example, a 16.2 kW, 36-inch unit pulls roughly 78 amps on a 208V single-phase circuit, while a 12 kW, 36-inch unit runs about 33.5 amps on 208V three-phase.
- Voltage: most models are ordered in a specific voltage and phase. Have an electrician check the circuit against the nameplate before delivery.
Either way, griddles produce grease-laden vapor and belong under a commercial exhaust hood that meets NFPA 96 and your local fire code. Your health department or local public health unit will expect this on the plan review.
Thermostatic vs Manual Griddle Controls
The thermostatic vs manual griddle choice comes down to who controls the plate temperature: the cook or the griddle.
Manual controls
A manual griddle has an infinite (or high-low) gas valve on each burner. The burner holds whatever output the cook sets, loaded or empty, and a skilled cook moves product between hotter and cooler zones. Manual griddles are simpler and usually cost less. The trade-off: the plate creeps hotter during slow periods and drops under a full load, so results depend on whoever is at the station.
Thermostatic controls
A thermostatic griddle has a thermostat on each burner or element that cycles the heat to hold the temperature dialed for that zone. Eggs can run low at one end and burgers hot at the other while the griddle does the adjusting. That matters for franchise specs, rotating staff and any item that has to come out the same every shift. Thermostatic models also use less energy at idle, and both ENERGY STAR and Natural Resources Canada certify only thermostatically controlled griddles.
Ranges vary by model, so compare the dial range to your menu. On the griddles we carry, thermostatic ranges run from about 150°F at the low end to 450°F, 500°F or 550°F at the top. Remember that a thermostat controls the plate, not doneness. Use a probe thermometer: the FDA Food Code calls for ground beef patties to reach 155°F for 17 seconds, while Health Canada recommends 71°C (160°F) for ground beef. Provincial and local rules apply in Canada.
| Factor | Manual | Thermostatic |
|---|---|---|
| Consistency across cooks | Depends on skill | Repeatable by setting |
| Behavior in slow periods | Plate climbs; watch for scorching | Holds the set temperature |
| Energy at idle | Burners stay at full setting | Burners cycle down |
| Parts to service | Fewer | Thermostats and safety valves |
| ENERGY STAR eligible | No | Possible, if the model is certified |
| Best for | Skilled crews, searing, simple menus | Breakfast, franchise lines, mixed menus, new staff |
Griddle Plate Thickness and Material
Plate thickness
Griddle plate thickness controls the balance between heat-up speed and recovery. A thin plate heats quickly but loses temperature fast when cold product goes down, and repeated heating and cooling can warp it over time. A thick plate takes longer to preheat but stores much more heat, so it recovers between loads and holds a flatter temperature across the surface.
- 3/4 inch: common on countertop and medium-duty units; fits cafes and moderate breakfast volume.
- 1 inch: the heavy-duty standard for frozen patties, busy breakfasts and full-plate loads.
- Thinner: light-duty only; expect cooler spots and slower recovery.
Plate material
| Surface | Strengths | Watch-outs |
|---|---|---|
| Polished steel | Durable, forgiving, holds heat, accepts a scraper and griddle brick | Needs seasoning after cleaning; radiates the most heat into the kitchen; the most effort to clean |
| Chrome-plated | Less flavor carryover, easier release for eggs and fish, less radiant heat at the cook | The chrome is a finish: no griddle bricks, wire brushes or tapping spatulas; use chrome-safe pads and scrapers |
| Composite (aluminum core, stainless face) | Fast, even heating and recovery; mild-detergent cleanup | Avoid aggressive abrasives; typically a premium option |
| Cast iron | Good heat retention on smaller countertop units | Must be kept seasoned and dry to prevent rust |
A chrome griddle earns its place when one plate handles very different foods through the day or a cook works it all shift. Vulcan's plate comparison rates chrome lowest for radiant heat and flavor transfer, and steel the most work to clean. If you mainly sear proteins and your crew knows steel, steel is the practical choice.
Sizing a Griddle by Menu and Volume
Width is measured in 12-inch zones, because that is how burners and thermostats are laid out. Count the zones your peak hour needs, then decide on depth.
Rule of thumb: zones per menu
- One zone per temperature you need at the same time. A breakfast line running eggs (low), pancakes (medium) and bacon or hash browns (high) needs at least three zones, which means a 36-inch griddle.
- Add a zone for every product that dominates the peak. If burgers make up half your lunch tickets, give them two zones.
- Add a holding area. A cooler zone at one end, or the back rows of a deep plate, keeps finished product warm without crowding the cooking area.
Quick capacity math
To estimate how much fits, divide each dimension of the cooking surface by the size of your product plus spacing. A 5-inch patty footprint (portion plus room to flip) fits 2 across and 4 deep on a 12-by-24-inch zone, or about 8 patties per zone, so a 36-by-24-inch plate holds roughly 24 at once. Repeat the math with your own portions and the cooking-surface size from the spec sheet.
| Width | Zones | Typical fit |
|---|---|---|
| 12–15 in | 1 | Concession stands, bars, a side task such as toasting buns or grilled cheese |
| 24 in | 2 | Cafes, delis and small breakfast menus |
| 36 in | 3 | The most common restaurant size; breakfast and lunch on one plate |
| 48 in | 4 | Busy diners and burger concepts |
| 60–72 in | 5–6 | High-volume breakfast, institutional and banquet kitchens |
Depth: plates run roughly 20 to 24 inches deep. A 24-inch plate adds a back row for holding, provided the unit still fits your counter and hood.
What to Look for Before You Buy
- Grease management: a wide, fully welded trough, a large removable drawer and welded splashes cut closing time.
- Clearances: check the spec sheet's clearance to combustible and non-combustible construction. Some gas griddles are approved for non-combustible locations only.
- Mounting: countertop griddles need a stand or counter that can carry the unit's weight (roughly 200 to 400 pounds for the 36-inch models featured below) and sit on legs of the specified height.
- Flame safety: on gas thermostatic models, look for pilot safety valves that shut off gas if the pilot goes out.
- Certifications (US and Canada): look for a sanitation listing (NSF or ETL Sanitation) and a safety listing recognized in your country. In the US that is typically UL, ETL or CSA; in Canada, look for marks such as CSA, cUL, cETL or cQPS that show the unit was certified to Canadian standards. Inspectors in both countries will look for them.
- Energy and rebates: ENERGY STAR caps idle energy at 2,650 Btu/h per square foot for gas griddles and 320 W per square foot for electric. Check the ENERGY STAR product finder for a specific model, then ask your utility (US) or your provincial utility and NRCan programs (Canada) about current foodservice rebates.
- Warranty: coverage on the griddles we carry ranges from one to three years parts and labor. Read the terms for commercial use.
Griddles Worth Shortlisting
Here are 36-inch models from six brands that show how the decisions above play out. Browse the full commercial griddles collection for other widths.
Manual gas
- Vulcan VMG36 manual gas griddle: three 27,000 BTU/hr burners, each with its own infinite heat valve, under a 36-by-24-inch, 1-inch polished steel plate, with a standing pilot.
More options: manual gas griddles.
Thermostatic gas
- Wolf ASA36 thermostatic gas griddle: three snap-action thermostats adjustable from 200°F to 550°F, 81,000 BTU/hr, a 1-inch polished steel plate and pilot safety valves. CSA design certified and NSF listed.
- Noriota NTG36 thermostatic gas griddle: three 200°F to 450°F zones, 90,000 BTU/hr and a 1-inch plate. Ships for natural gas with the LP kit included, and is ETL listed for the US and Canada plus ETL Sanitation listed.
- American Range ARTG-36-24 thermostatic griddle: a 24-inch-deep, 1-inch plate with a thermostat on each of three 30,000 BTU/hr burners (250°F to 500°F). cETLus and ETL Sanitation listed, with a three-year parts and labor warranty.
More options: thermostatic gas griddles.
Electric
- BakeMax BMPLS7IE030 electric griddle: a 3/4-inch steel plate with three thermostatic zones from 150°F to 500°F and 12 kW. It ships 208V three-phase and can be field converted to single phase. ETL Electrical and ETL Sanitation listed.
- Omcan CE-CN-53303F chrome electric griddle: a food-grade chrome surface measuring 33.6 by 19 inches, 10.8 kW on 240V single phase and front and rear grease grooves. cQPSus certified.
More options: electric griddles.
Care and service: season steel plates after every deep clean, never cool a hot plate with ice or water, and keep bricks and wire brushes off chrome. Before any service, shut off gas or power and let the plate cool. Valve, thermostat and pilot work belongs to a licensed technician, and the manufacturer's manual for your unit always takes precedence.
Need a second opinion on a spec sheet, utility hookup or certification? Our team can help you compare models before you order.
Frequently Asked Questions
Is a gas or electric griddle better for a restaurant?
Neither wins everywhere. Choose gas if the line already has gas service. Choose electric if the building has no gas, but full-size units need a dedicated high-amperage circuit.
What griddle plate thickness should I buy?
For heavy use, frozen product or full-plate loads, choose a 1-inch plate. A 3/4-inch plate suits moderate volume and countertop work. Thinner plates heat faster but recover slowly and are best kept for light-duty use.
Are thermostatic griddles worth the extra cost?
Usually, if you cook to written temperatures, have high staff turnover or run several products at different heats. A skilled crew on a simple sear-focused menu often does fine with manual.
What is the advantage of a chrome griddle?
A chrome surface carries less flavor from one item to the next, releases delicate foods more easily and throws less heat at the cook. It needs chrome-safe cleaning tools, so it is not the right pick for a crew used to scraping steel with a griddle brick.
Does a commercial griddle need a hood?
Yes. Griddles produce grease-laden vapor, so plan for a commercial exhaust hood that meets NFPA 96 and local code in both the US and Canada.